芘高效降解菌ZQ_5的培养条件及无机元素对其降解效率的影响

以从我国最大的石油污水灌区之一——沈抚灌区污染土壤分离到的以芘为惟一碳源、能源生长的高效降解菌株ZQ5为实验材料,通过对菌株ZQ5培养条件的优化,以及采用摇瓶振荡培养方法测定菌株ZQ5对不同浓度芘的降解率,表明：菌株ZQ5在30℃振荡培养16 d后对150 mg/L芘的降解率为90.31%。通过模拟稻田施用N、P和K肥等的土壤环境,探索了无机营养元素对降解菌ZQ5降解能力的影响,发现土壤中混合加入N、P和K无机营养元素的降解率能达到82%以上,比单加某种营养元素对降解菌ZQ5的降解效果好。本研究结果可以指导稻田PAHs的原位生物修复。     

Effects of perfluorinated compounds on development of zebrafish embryos

Perfluorinated compounds (PFCs) have been widely used in industrial and consumer products and frequently detected in many environmental media. Potential reproductive effects of perfluorooctanesulfonate (PFOS), perfluorooctanoic acid (PFOA) and perfluorononanoic acid (PFNA) have been reported in mice, rats and water birds. PFOS and PFOA were also confirmed developing toxicants towards zebrafish embryos; however, the reported effect concentrations were contradictory. Polyfluorinated alkylated phosphate ester surfactants (including FC807) are precursor of PFOS and PFOA; however, there is no published information about the effects of FC807 and PFNA on zebrafish embryos. Therefore, this study was conducted to determine the effects of these four PFCs on zebrafish embryos. Normal fertilized zebrafish embryos were selected to be exposed to several concentrations of PFOA, PFNA, PFOS or FC807 in 24-well cell culture plates. A digital camera was used to image morphological anomalies of embryos with a stereomicroscope. Embryos were observed through matching up to 96-h post-fertilization (hpf) and rates of survival and abnormalities recorded. PFCs caused lethality in a concentration-dependent manner with potential toxicity in the order of PFOS > FC807 > PFNA > PFOA based on 72-h LC(50). Forty-eight-hour post-fertilization pericardial edema and 72- or 96-hpf spine crooked malformation were all observed. PFOA, PFNA, PFOS and FC807 all caused structural abnormalities using early stages of development of zebrafish. The PFCs all retarded the development of zebrafish embryos. The toxicity of the PFCs was related to the length of the PFC chain and functional groups.     

陶瓷印花废水处理的混凝剂及工艺条件

采用混凝剂聚合氯化铝（PAC）、聚丙烯酰胺（PAM）、聚合硫酸铁（PFS）对陶瓷印花废水进行混凝沉降处理，监测水样的吸光度、浊度、悬浮物，以脱色率、浊度去除率、悬浮物去除率评价混凝处理的效果。结果表明：PAC是陶瓷印花废水沉降处理的理想混凝剂；水样的吸光度、浊度、悬浮物随混凝剂用量增大和沉降时间延长而呈降低趋势，而脱色率、浊度去除率、悬浮物去除率随混凝剂和沉降时间的增大呈增大的趋势；PAC投加量为20mg／L，沉降时间约为24h，水样脱色率达到90．0％，而当PAC投加量达到100mg／L，沉降时间约为4h，陶瓷印花水的脱色率可达到96．0％。证明了药剂用量的增加与沉降时间的延长对混凝过程具有增效作用。     

纤维素降解细菌筛选及降解特性分析

基于获得高效纤维素降解细菌的目的,通过LB培养基的培养以及刚果红培养基的筛选,从牛粪堆肥中筛选获得2株高效纤维素降解细菌。经鉴定,分别为枯草芽胞杆菌(Bacillus subtilis)和地衣芽胞杆菌(Bacillus licheniformis)。所筛选得到的菌种具有很高的滤纸降解能力,可在6d内使滤纸剧烈崩溃,振摇成均匀糊状;其中,地衣芽胞杆菌的羧甲基纤维素钠酶活峰值在发酵第4天达到峰值(237U/g)。     

动态污水处理过程的多模型动态矩阵控制

针对活性污泥法污水处理系统的强耦合和动态变化特性,提出一种用于前置反硝化脱氮工艺的多模型动态矩阵(DMC)解耦控制方法;通过K-均值聚类分析法对外界入水中氨氮浓度进行聚类,获得以聚类中心为入水氨氮浓度的静态模型集合,分别设计线性DMC解耦控制器;再以当前时刻外界进水氨氮浓度和聚类中心为基本元素,构造切换函数,实现多模型切换。将该方法应用于活性污泥1号模型(ASM1)中,获得了较好的动态仿真效果。     

微电解预处理靛蓝牛仔布印染废水

靛蓝牛仔布印染废水组分复杂,浓度高、水量大,属于难处理的工业废水,为了有效降低后续生物处理单元的负荷,采用铁炭微电解工艺对该废水进行预处理；通过正交实验考察pH、反应时间及铁炭比处理效果的影响规律及COD去除反应动力学,并对各因素作了单因素影响实验,确定了最佳工艺条件.结果表明,铁炭微电解法是预处理靛蓝牛仔布印染废水的一种有效方法,在Fe/C为2:1、pH为3的条件下反应90 min,铁炭微电解出水COD的去除率在49.2％,色度去除率达到80％,该印染废水经微电解处理后,BOD5/COD比值可从原来的0.248上升至0.436,可生化性明显提高.此外,微电解预处理靛蓝牛仔布印染废水中COD的去除反应符合二级反应动力学规律.     

污泥转移SBR工艺处理低浓度生活污水

污泥转移SBR工艺是一种通过内部污泥回流实现污泥在不同SBR隔室间转移,从而增加污泥利用效率,提高系统除污效能的新工艺。以设计规模为240 m3/d、处理低浓度生活污水的工艺系统为对象,研究了新工艺在不同泥转移量(污泥回流比)下的除污性能,并与系统以传统SBR方式运行的情况进行了对比。结果表明,新工艺可以有效提高SBR反应器的容积利用率;采用30%的污泥回流比进行污泥转移,新工艺的处理能力比传统SBR工艺提高近1/2,除磷效率从46%提升至85%。出水各项水质指标均能达到国家排放标准的要求。     

A survey on the utility of the USEPA CADDIS stressor identification procedure

The Environmental Protection Agency (EPA) has made available on the worldwide web a systematic stream stressor identification procedure, the “Causal Analysis/Diagnosis Decision Information System” or CADDIS. We report here the results of a survey of regulators and scientists in 11 states who use CADDIS or another stressor identification procedure in their work. The 13 survey questions address guidelines as to what impairment scenarios to approach with stressor identification, what information is needed to perform stressor identification, and what the stakeholder role is in performing stressor identification. At the time of this survey (the summer of 2009), the EPA CADDIS website was less commonly used among the state regulators surveyed than the published EPA stressor identification document on which it is based. The respondents generally find the EPA stressor identification procedure useful and capable of being adapted to their individual needs. Survey respondents all use stressor identification in their Total Maximum Daily Load work, but also in a wide variety of other applications. All the “types of evidence” included in the CADDIS stressor identification procedure are used by the practitioners surveyed with the exception of the results of ecological simulation models. While the CADDIS documentation encourages the involvement of stakeholders in stressor identification, most respondents do not assemble stakeholder teams of local officials and citizens to participate in stressor analyses.     

MnxCe1-xO2／γ-Al2O3催化剂的制备及其催化甲苯的燃烧性能

以γ-Al2O3为载体，以MnxCe1-xO2为催化活性组分，采用浸渍法制备了一系列负载型MnxCe1-xO2／γ-Al2O3催化剂（x=0、0．2、0．4、0．6、0．8、0．9、1），在固定床反应器中评价了催化剂对甲苯的催化燃烧性能。结果表明，MnxCe1-xO2／γ-Al2O3催化剂的催化活性与催化剂的焙烧温度、活性组分MnxCe1-xO2的负载量以及Mn、Ce摩尔比有显著关系，其中焙烧温度550℃、负载量为20％、Mn、Ce摩尔比为4：1时，即MnxCe1-xO2／γ-Al2O3催化剂对甲苯的催化性能最佳，反应温度为180℃时，甲苯的转化率达到95％。并在连续100h的稳定性操作后，催化剂的活性基本无变化。采用XRD、BET以及SEM等分析测试手段对催化剂的结构以及表面进行了表征。